In most cases, several components of backflow preventers can be replaced, such as rubber gaskets. This is a cost-effective repair option. But if the backflow preventer valve is very old or corroded, these repairs may not be possible. Your local Mr. Rooter Plumbing will assess the system to see if a repair is feasible.

Simply put, an open water heater system allows excess water pressure to make its way back into your cold water supply line and eventually out into the municipal water supply. A closed system does not allow excess pressure to make it back out into the municipal supply.

A backflow preventer is most often installed where municipal or well water enters the home. Another popular spot for a backflow preventer is at an irrigation system’s intake point.

When the water enters the valve at a pressure greater than what it’s been set to allow, the diaphragm and spring will contract and reduce the flow. The reverse is also true, however. If the water enters the valve at too low a pressure, the spring and diaphragm will expand and allow the water to exit through a larger hole.

This may be counterintuitive since it’s the opposite of how faucets work, so make sure you know what direction to turn in order to get your desired pressure.

After completing a repair service, we can also perform backflow prevention device testing to ensure the fix was effective.

Water heaters in Phoenix are typically capable of handling pressure lower than 80 psi. City officials, meanwhile, consider pressure ranging from 40 to 100 psi acceptable. If the pressure of the water arriving at your home reaches the upper end of that range, it will damage not only your water heater but other appliances and pipes as well.

© 2024 The Dwyer Group Canada, Inc. d/b/a Neighbourly. All rights reserved. Neighbourly is a registered trademark of Neighborly Assetco LLC. This site and all of its content is protected under applicable law, including laws of Canada and other countries. Each location is independently owned and operated. Territorial, provincial, and local laws may impact the services this independently owned and operated franchise location may perform at this time. Please contact the franchise location for additional information.

You’ll know this is the case when adjustments to your valve do not result in changes to your water pressure. The pressure may be consistently high regardless of your efforts and you’ll likely notice issues such as water hammers and dripping faucets.

Depending on the type of device, testing can be as simple as a visual inspection on some devices. Testing some devices requires the use of a precision-reduced pressure valve test tool. However, we recommend having your local plumber perform backflow prevention testing and explain the best solutions for any problems identified.

As their name would suggest, pressure reducing valves control the flow of water into your home. Without a pressure reducing valve, this water would travel through your plumbing at a rate unsuitable for residential use.

Now that you have a good understanding of how pressure reducing valves work, you should have an idea of what’s happening when you do the adjustments.

How can you tell whether it’s time to have a backflow preventer replaced? If the device needs extensive repairs, replacing it may be more economical and will get your water service back faster. Old and outdated backflow preventer valves are more likely to have more repair needs in the future, so keep your valve’s age in mind when making this decision.

If you’re experiencing increased or decreased water pressure due to an abnormality in your municipal water supply’s function, adjusting the valve may throw things out of wack when the system returns to normal.

A pressure reducing valve is typically close to your water shutoff valve. You’ll know you’re looking at the valve because it will have a gauge nearby.

Residential backflow preventers are designed to keep contaminated water from flowing into your home’s potable water supply. Without an operational backflow valve, sudden changes in water pressure can allow contaminated water to flow backward in the pipes, bringing harmful substances with it. Your local Mr. Rooter® Plumbing performs all backflow preventer valve services, including installation, repair, testing, and replacement.

Once you’ve determined the pressure, use a hand pump to raise it to a pressure equal that of your home’s water pressure. Don’t use an air compressor; doing so risks damage.

Do not make huge adjustments at once. Make no more than a quarter turn each time before taking a look at the gauge to see what effect you’re having.

It’s recommended that you check your water pressure at least once per year to ensure it’s at the desired level. As with most mechanical devices, however, your pressure reducing valve can begin to function improperly with time.

Searching through dozens of home service providers is a thing of the past. Rely on Neighbourly’s national network of trusted, local home service professionals for all your home service needs.

Knowing how to adjust a pressure reducing valve is an important part of any DIYer’s toolkit. Be it for a reverse osmosis system or other plumbing needs. it is for In this article, we’ll start from scratch and walk you through the process. We’ll also tell you everything you need to know about pressure reducing valves and why you might need to adjust yours in the first place.

If you have a closed water heater system, you will also need to adjust the pressure on your thermal expansion tank. To do this properly, you’ll need an air pressure gauge to test the existing pressure of your expansion tank. Attach the valve directly to the air inlet valve on the tank.

With locations across Canada, Mr. Rooter Plumbing is your local source for backflow preventer installation, repair, and replacement. Think of backflow prevention as inexpensive insurance; you’ll never know when you need it, but when you do, you’ll be glad you have reduced the chances of contamination of your home water supply. Protect your home and gain peace of mind. Give Mr. Rooter a call or request an estimate online.

© 2024 The Dwyer Group Canada, Inc. d/b/a Neighbourly. All rights reserved. Neighbourly is a registered trademark of Neighborly Assetco LLC. This site and all of its content is protected under applicable law, including laws of Canada and other countries. Each location is independently owned and operated. Territorial, provincial, and local laws may impact the services this independently owned and operated franchise location may perform at this time. Please contact the franchise location for additional information.

When you notice water coming out of a backflow valve, the first thing to do is turn off the water main to limit water contamination and property damage. Then call your local Mr. Rooter to inspect and repair the valve.

There are a few places you can attach the gauge to get a good reading. As long as the fixture is downstream of the valve, it’s doesn’t particularly matter. Many people attach the gauge to a water heater drain valve or simply a faucet.

You can also find other useful guides like AC troubleshooting or Why is Your Air Conditioning Unit On the Roof in Arizona?

If you think you need to replace your pressure reducing valve, you’d be smart to contact a professional to do the job. It can be a confusing process for inexperienced DIYers as it requires soldering, plumbing work, and potentially the installation of other equipment to mitigate any issues you come across.

When thermal expansion occurs, this can be dangerous. To avoid this danger, you will have to match the pressure of your regulator to the pressure of your expansion tank.

If you’re unsure of what you’re doing and live in the Phoenix area, give us a call at American Home Water and Air. We’ve been repairing residential water and HVAC systems for more than 30 years and we’d be delighted to serve you. We also provide top-notch HVAC and plumbing services in Gilbert, Glendale, Goodyear, Buckeye, and many other areas surrounding Phoenix, AZ.

If this doesn’t make total sense to you, don’t worry. The exact mechanics and physics of the process confuse even some experienced plumbers. What everyone does know is that the process works.

Copyright ©2024 Mr. Rooter. All rights reserved. This information is not intended as an offer to sell, or the solicitation of an offer to buy, a franchise. It is for information purposes only. Mr. Rooter is a registered trademark of Mr. Rooter LLC

Once the valve has been installed professionally, adjusting it on your own is fairly straightforward presuming you have a solid understanding of the steps outlined above.

Before you make any adjustments to your pressure reducing valve, you need to understand the existing circumstances. While you may know your pressure is too high due to symptoms such as dripping faucets, you want to get an exact reading on the pressure.

Inside the valve, there are a spring and diaphragm. These two elements interact with incoming water pressure, either contracting or enlarging the hole that your water ultimately passes through.

Many valves have a nut, screw, or knob attached to them that allow you to do the actual adjusting. Turning the screw or knob clockwise typically increases the water pressure while turning it counter-clockwise lowers the pressure.

Also, note that adjusting your pressure reducing valve setting without fully understanding what you’re doing can lead to issues. Setting the pressure too high wastes water and can be harmful to your appliances. In extreme cases, your water heater can explode. Appliances like water softeners can also face damage.

Your pressure reducing valve setting will determine what it considers acceptable at both the upper and lower limits of its range.

For this reason, you’d be wise to contact your water department to see if the issue lies with them. If not, it’s possible that your valve has gone out of wack somehow and requires adjustment.

Most valves have a locking nut. Once you unscrew this nut, you will be able to turn the adjustment screw, knob, or bolt. Adjust it until the pressure shown on your gauge reaches the desired level. For most residential purposes, that means a pressure below 80 psi.

Make sure you lock the adjustment nut on your pressure reducing valve. This will prevent the screw from turning easily, which would undo your adjustments.

Want to read more? Check out 6 Air Conditioner Fire Prevention Measures and How To Protect Yourself From Poor Air Quality In Phoenix.

In other words, if you’re uncertain about what you’re doing, contact professionals like our technicians at American Home Water and Air.

A pressure reducing valve is an important part of your residential water system. It allows you to adjust the pressure of water arriving in your home to a level that is suitable for your appliances.

A pressure reducing valve usually resembles a bell or dome. As mentioned earlier, you’ll usually see it alongside a gauge. It may be built right into your water meter. In most cases, however, you’ll find the valve in the form of a separate device that lies after the meter within your home’s water supply chain.

Before you go about adjusting the pressure, contact your municipality to ensure the abnormal pressure is not just a temporary issue with their systems.